Fr français
+44 (0)1462 424700 +44 (0)1462 424700 English Speaking Only +46 (0)8 559 2 666 2
+49 (0)30 6188845 +49 (0)30 6188845 English Speaking Only +45 (0)36 988 355  
Products Services Careers About WPI     Contact Us Quote
 OXYMINI and OXYMICRO
  A new generation of fibre optic oxygen sensors based on luminescence lifetime.  

A new generation of fibre optic oxygen sensors based on luminescence lifetime the OxyMini system is optimized for process control and biotechnology applications. The OxyMicro is designed for medical research applications including implanting into tissues, cell cultures, profiling of biofilms and sediment related bioassays. The measurement principle of the sensor system is based on the detection of oxygen concentration as a function of luminescence lifetime either in dissolved or gaseous phase environments.

Benefits

  • Oxygen is not consumed during the experiment

  • Immune to electrical and magnetic interference

  • Excellent long-term stability

  • No lengthy polarization necessary (e.g., as Clark-type oxygen electrodes require)

  • Fast response time < 0.5 s for MicroTip sensors

  • Probe size of MicroTip sensors as small as 50 µm

  • Measurement is feasible in dry gas

  • Optical isolation of sensor tip available for fluorescent or photosynthetically active samples

Measurement Principle

Conventional fibre-optic oxygen sensor systems based on intensity measurements are limited in their accuracy by light source stability and ambient light fluctuations. Using a luminescence lifetime detection, measurements are not affected by light source stability, intensity fluctuations caused by fibre bending or changes of the optical properties of the sample (turbidity, refractive index, coloration, etc.). These advantages make WPI’s OxyMini and OxyMicro the most advanced and reliable fibre-optic oxygen system available.

Calibration: The sensors can be calibrated by a simple two point calibration, 100% air-saturation and 0% air saturation.

OxyMini and OxyMicro oxygen meters: The OxyMini and OxyMicro fibre optic oxygen meters are compact, easy to transport. The instruments are designed for in/outdoor use and can be connected to a PC via a RS232 interface. Data can be visualized, analyzed and stored with the supplied software. A full range of sensors covering most biomedical applications are available.
 

OXYMINI  

The OxyMini is a single-channel fibre optic oxygen meter for WPI’s fibre optic oxygen minisensors. These sensors are based on 2 mm polymer optical fibres and have a length of 2.5 m. A wide range of applications is possible with these sensors. 

  • Process control: bottling plant in breweries and quality control of packages
  • Biotechnology: Control of cell culture media and non-invasive control of bioreactors
  • Implantation of oxygen sensors into soil and trees. 

MiniTip
This oxygen dipping probe (WPI #501641) has a tip diameter of 4 mm and consists of a polymer optical fibre, with a oxygen sensitive coating. The MinTip’s range is 0 to 100%. This robust sensor has a response time of approximately 40s.

 

MiniFlow
The MiniFlow oxygen probe (WPI #501642) is a miniaturized fibre optic chemical sensor integrated in a T-shape flow through cell. The standard T-shape flow cell can be easily connected via Luer-Lock adapters to external tubings. Liquids (e.g., water, blood, etc.) can be pumped through the cell. The sensor has a response time of approximately 40 s and an excellent long-term stability.

 

MiniFoil
WPI offers the sensor material on a 1 cm2 support disk made of polyester. This material can be glued, for example, inside glass vials and the oxygen concentration can be measured non-invasively and non-destructively from outside through the wall of the flask. A plastic fibre optic cable (WPI #501644, WPI #501645) is used to illuminate the sensor foil. The wall of the flask must be transparent/non-fluorescent. Response time of approximately 50 s. The material can be implanted into animal tissues or custom-made housings.

Download Page from Catalogue
 

 
 

OXYMICRO

The OxyMicro is a single channel fibre optic oxygen meter for WPI’s fibre optic oxygen microsensors. Applications include:

  • Oxygen profiles of marine sediment, soils, or tissue
  • Implantation into living tissue (e.g., heart or muscle tissue)
  • Control of cell culture media in Biotechnology. 

MicroTip
The MicroTip (WPI #501656) is a needle-type oxygen micro sensor designed for applications where a small tip size of 50 µm and a fast response time (t90) of 1 s are necessary. The oxygen sensitive sensor tip consists of 140 µm fibre tapered to a 50 µm tip. The sensor is housed inside a stainless steel needle of 22 mm length and 0.4 mm diameter. This allows penetration through a septum rubber or similar material. These sensors are ideal for oxygen profiling in sediments and biofilms.

MicroFlow
The MicroFlow fibre optic oxygen sensor (WPI #501657) is a miniaturized fibre optic chemical sensor optimized for fast response time (t90 < 1 sec in gases, < 5 sec in liquids). The tiny probe has a tip size of 50 µm and is integrated in a T-shape flow cell for easy connection via Luer-Lock adapters to external tubings. Liquids (like water, blood, etc.) can be pumped through the cell.

MicroImplant
The MicroImplant fibre optic oxygen sensor (WPI #501658) is a implantable probe (IMP) with a tiny probe tip size 50 µm, an exposed fibre length of 5 mm and a jacket diameter of 900 µm. The IMP sensor was successfully implanted in crabs, fishes and soil.

Download Page from Catalogue

 
 

 
 

 

MODELS
MINISENSOR SYSTEM
OXY-MINI Fibre-optic oxygen meter for minisensors Add to Quote Basket
OXY-MINI-AOT* Fibre-optic oxygen meter for minisensors Add to Quote Basket
MINISENSORS
501641 MiniTip, fibre-optic oxygen sensor (2.3 mm OD) Add to Quote Basket
501642 MiniFlow, flow-through cell with integrated planar oxygen sensor Add to Quote Basket
501643 MiniFoil, planar oxygen-sensitive foils, 1x1 cm (1 cm2) Add to Quote Basket
501644 Polymer optical fibre with 1 SMA connector Add to Quote Basket
501645 Polymer optical fibre with 2 SMA connectors Add to Quote Basket
MICROSENSOR SYSTEM
OXY-MICRO Fibre-optic oxygen meter for microsensors Add to Quote Basket
OXY-MICRO-AOT* Fibre-optic oxygen meter for microsensors Add to Quote Basket
MICROSENSORS
501656 MicroTip, needle-type housing fibre-optic oxygen sensor Add to Quote Basket
501657 MicroFlow, flow-through housed oxygen microsensor Add to Quote Basket
501658 MicroImplant, implantable oxygen microsensors Add to Quote Basket
*AOT meter contains two analogue outputs and one trigger input
 
| Demo Request  | Manual 
                             Note that WPI Equipment is NOT Designed for Human Use

Bookmark and Share

Copyright © World Precision Instruments 2012 | For questions & comments pertaining to this website, contact: webmaster ^top^

Follow us:
 

 

We take
 

Privacy Statement